The OFFICIAL "I have a wheel offset / tire fitment question!" thread
#2251
Registered Member
Found a good set of used forged wheels for a fair price that I'd love to put on my '12 G37X. I know they'd fit, but I want to double-check that the offset won't have a significant effect on driving/handling. I'm still relatively new when it comes to most of this, and I have a hard time understanding the effect of the change in scrub radius. Anyway, the wheels are:
The wheels are 18x8 et38, and the car is fully stock at the moment.
I know it's not a huge difference from stock. However, like I said, I'm new to this and just want to double-check it won't change the car too much, if at all.
Thanks in advance.
The wheels are 18x8 et38, and the car is fully stock at the moment.
I know it's not a huge difference from stock. However, like I said, I'm new to this and just want to double-check it won't change the car too much, if at all.
Thanks in advance.
#2252
Registered Member
iTrader: (1)
I have a 2014 Q60/G37 coupe AWD, I will be lowering it on Swift springs.
Looking to do a staggered setup on it (keeping tire diameters the same) would these wheels/tread widths be OK on my coupe?:
Front 19x8.5 +30 offset 245 wide tire
Rear 19x9.5 +40 offset 275 wide tire
I'm hoping to keep a flush look, I don't like wheel poke.
Looking to do a staggered setup on it (keeping tire diameters the same) would these wheels/tread widths be OK on my coupe?:
Front 19x8.5 +30 offset 245 wide tire
Rear 19x9.5 +40 offset 275 wide tire
I'm hoping to keep a flush look, I don't like wheel poke.
#2253
I know, it's a little dirty, but I put these wheels on this weekend and it is currently raining here so I'll be doing a full wash/polish/wax this upcoming weekend.
2009 6MT S Coupe
Square Set Up:
18X9 ET35 O.Z. Racing Ultraleggera
Hankook Ventus RS-3v2 275/35ZR18
Currently stock suspension
KW V1s will be installed soon
Clears BBK
2009 6MT S Coupe
Square Set Up:
18X9 ET35 O.Z. Racing Ultraleggera
Hankook Ventus RS-3v2 275/35ZR18
Currently stock suspension
KW V1s will be installed soon
Clears BBK
The following users liked this post:
blnewt (05-02-2018)
#2254
I had a 2007 G35x on 20x10 +38 with 255/35/20 all around and was on swift springs. Was pretty much a perfect fit. I had to shave the face of my calipers to make the wheel fit, but this was because of the design of the wheel faces.
#2255
19x10 +20 will they fit
I found a set of Weds Cerberus 2 19x9.5 +20 front, and 19x10 +20 rear. I want to fit these on a 2009 G37x sedan. Can I make it fit with -2 camber and reasonable tires (for example 255/40 or maybe 245/40)?
The car car will be dropped on Feal 441 coilovers with Spc camber kit front and back. About to pull the trigger one these wheels tonight hopefully if I get feedback that makes sense. I really don’t want to pull or roll fenders don’t mind a little poke.
Appreciate the help.
The car car will be dropped on Feal 441 coilovers with Spc camber kit front and back. About to pull the trigger one these wheels tonight hopefully if I get feedback that makes sense. I really don’t want to pull or roll fenders don’t mind a little poke.
Appreciate the help.
Last edited by Louis Reed; 05-01-2018 at 06:20 PM. Reason: Additional information
#2256
Movin On!
iTrader: (13)
I have a 2014 Q60/G37 coupe AWD, I will be lowering it on Swift springs.
Looking to do a staggered setup on it (keeping tire diameters the same) would these wheels/tread widths be OK on my coupe?:
Front 19x8.5 +30 offset 245 wide tire
Rear 19x9.5 +40 offset 275 wide tire
I'm hoping to keep a flush look, I don't like wheel poke.
Looking to do a staggered setup on it (keeping tire diameters the same) would these wheels/tread widths be OK on my coupe?:
Front 19x8.5 +30 offset 245 wide tire
Rear 19x9.5 +40 offset 275 wide tire
I'm hoping to keep a flush look, I don't like wheel poke.
#2258
Movin On!
iTrader: (13)
I found a set of Weds Cerberus 2 19x9.5 +20 front, and 19x10 +20 rear. I want to fit these on a 2009 G37x sedan. Can I make it fit with -2 camber and reasonable tires (for example 255/40 or maybe 245/40)?
The car car will be dropped on Feal 441 coilovers with Spc camber kit front and back. About to pull the trigger one these wheels tonight hopefully if I get feedback that makes sense. I really don’t want to pull or roll fenders don’t mind a little poke.
Appreciate the help.
The car car will be dropped on Feal 441 coilovers with Spc camber kit front and back. About to pull the trigger one these wheels tonight hopefully if I get feedback that makes sense. I really don’t want to pull or roll fenders don’t mind a little poke.
Appreciate the help.
#2262
Registered Member
I know, it's a little dirty, but I put these wheels on this weekend and it is currently raining here so I'll be doing a full wash/polish/wax this upcoming weekend.
2009 6MT S Coupe
Square Set Up:
18X9 ET35 O.Z. Racing Ultraleggera
Hankook Ventus RS-3v2 275/35ZR18
Currently stock suspension
KW V1s will be installed soon
Clears BBK
2009 6MT S Coupe
Square Set Up:
18X9 ET35 O.Z. Racing Ultraleggera
Hankook Ventus RS-3v2 275/35ZR18
Currently stock suspension
KW V1s will be installed soon
Clears BBK
#2263
Yes, I did, I couldn't pass them up. He's only a few miles from me so it was an quick and easy pick up, making it an even better deal! Real nice guy too, chatted with him for a little while.
#2264
Registered Member
Yeah, I contacted him that day too, but unfortunately a 9" wheel was too narrow for my purposes. Glad that he was able to sell so quickly and you seem to enjoy them. It looks good! Needs a bit more sidewall when you're done with those though. :P
#2265
Registered Member
iTrader: (2)
My brother has a set of Jongbloed 308 Aero wheels that are 18x10.5 but not sure on offset. From what I can measure, my guess is it in the range of 55-60 mm offset. Anyone know if these will contact anything if I tires to run a square setup on this? I have a sedan.
I believe I’ve read somewhere that anything above ET 50 on a 10.5 in the front will contact the arm but I can’t find where I read that to verify. I feel that the rear should fit.
Thanks
Latez
I believe I’ve read somewhere that anything above ET 50 on a 10.5 in the front will contact the arm but I can’t find where I read that to verify. I feel that the rear should fit.
Thanks
Latez