DBALL/DBALL2 Malfunctions Thread
What steps are you following to learn the key? Also, make sure the over-ride switch for the DBALL is "off" when learning the key. "Off" does not mean the box is off. It means the over-ride is off, which means the box is on.
I've tried with the ignition off, acc and on positions. With the red and blue connectors only attached to the module, the light is green for 3 seconds and the door unlocked. If I add the black connector on the other side, the light is solid orange for a couple of seconds, then flashes orange 6 times. After both of those scenarios, it does nothing.
The bypass switch is off.
Thank you
Tom
The bypass switch is off.
Thank you
Tom
I've tried with the ignition off, acc and on positions. With the red and blue connectors only attached to the module, the light is green for 3 seconds and the door unlocked. If I add the black connector on the other side, the light is solid orange for a couple of seconds, then flashes orange 6 times. After both of those scenarios, it does nothing.
The bypass switch is off.
Thank you
Tom
The bypass switch is off.
Thank you
Tom
When the box is flashing orange, did you hit the unlock button on the fob? If not, you need to do that, then put the fob into the slot in the car. At that point the box should still be orange and that's when you press the brake pedal all the way down until the box flashes green then goes out. Have you tried those things before?
I never got it to flash orange as the instructions say. I'm wondering if I have a bad connection from the BCM and it's missing a signal. I'm going to look at it again, in the morning. I'll post back what happens.
I thought you said it did flash orange at first. Also, I don't think you mentioned if you bought the DBALL with the correct firmware already installed, or if you did it yourself. How did the firmware for the G37 get on the box? A bad connection was my next guess. Post back with what you find out.
Registered User
Joined: May 2014
Posts: 3
Likes: 0
help
I'm having the some issues on my 2011 g. My car won't start remotely after a few weeks. I hit the unock on fob 3x and nothing, repeat the process and nothing... Then the alarm goes off! I had it professional install and I've taken it back three times already and going back for the fourth and final time. 1st time they flash it to a uk firmware, it worked a few weeks then stopped. 2nd they replaced the kit, it work a few weeks, and then stopped. 3rd time they got support on the phone for assistance, they said xpress had them flash it for a different car and flash it back to infiniti g37, GUESS WHAT? it worked a few weeks and stopped. So I'm scheduled to take it back next week and they will contact xpresskit again for support. I'm like WTF! I was planning to get the viper smart start but it use dball2 as well.. So it will be an ongoing issue.
Registered Member
Joined: Mar 2015
Posts: 4
Likes: 0
Hello guys, I been looking around the forums and I found this older thread. I have the dball 2 installed in my G37 and I am having this weird issue. Once I start my car with the factory fob, I am unable to pop the trunk using the factory fob. I have to walk to the trunk with the key and then press the trunk button on the car for it to open.
Also the car no longer beeps using the door buttons on the outside of the doors as well as pressing the trunk button on the car either.
But when the car is off everything works the way it originally did. Trunk release on the fob works. Beeps when I use the physical buttons on the car to indicate its locked or unlocked.
Also the car no longer beeps using the door buttons on the outside of the doors as well as pressing the trunk button on the car either.
But when the car is off everything works the way it originally did. Trunk release on the fob works. Beeps when I use the physical buttons on the car to indicate its locked or unlocked.
Thread
Thread Starter
Forum
Replies
Last Post
blnewt
D.I.Y. Installations/Modifications
37
Oct 17, 2020 11:12 AM
