Help Soft Clutch Pedal in the Morning
#16
Administrator
Thread Starter
iTrader: (9)
Hey Jsolo... for the CMC, this guy here?
http://www.zspeedperformance.com/Clu...?categoryId=-1
Curiously, Amazon doesn't think this "fits my car". And Zspeed is asking a lot less than Z1. All which leads me to look for more corroboration.
http://www.zspeedperformance.com/Clu...?categoryId=-1
Curiously, Amazon doesn't think this "fits my car". And Zspeed is asking a lot less than Z1. All which leads me to look for more corroboration.
#17
Just say no!!!!!
iTrader: (14)
I thought RJM had a heavy duty cmc option available?
Widest engagement (large friction zone window) means more movement of the pedal for the same movement of the master, right? So the question is, when bleeding, did your tech do anything to this adjustment or just left it as is? It's a bit of a catch 22 I suppose. If the mc is moving little volume of fluid, it takes many pumps to build up pressure/move fluid out. On the other hand if your mc is questionable, then by having it operate in an area it doesn't normally operate in could have put more wear on the cup inside the master.
Also, iirc, any time you change the adjustment of the pedal ****, the limit switches should be readjusted and the pedal recentered so that mc pushrod is perpendicular to mc shaft (not particularly in that order but you get the idea). If the pushrod is being pushed at an angle then uneven internal wear would result.
I'd see how much the rjm master is. On the page I just set it as a kit with the pedal, not separately. $100 isn't bad for the oe master.
Widest engagement (large friction zone window) means more movement of the pedal for the same movement of the master, right? So the question is, when bleeding, did your tech do anything to this adjustment or just left it as is? It's a bit of a catch 22 I suppose. If the mc is moving little volume of fluid, it takes many pumps to build up pressure/move fluid out. On the other hand if your mc is questionable, then by having it operate in an area it doesn't normally operate in could have put more wear on the cup inside the master.
Also, iirc, any time you change the adjustment of the pedal ****, the limit switches should be readjusted and the pedal recentered so that mc pushrod is perpendicular to mc shaft (not particularly in that order but you get the idea). If the pushrod is being pushed at an angle then uneven internal wear would result.
I'd see how much the rjm master is. On the page I just set it as a kit with the pedal, not separately. $100 isn't bad for the oe master.
The following users liked this post:
Rochester (10-16-2018)
#19
Administrator
Thread Starter
iTrader: (9)
Hey Rochester, that CMC for the 370Z is a perfect fit on the G37. See the link for my impressions.
https://www.myg37.com/forums/showpost.php?p=4142458&postcount=28
https://www.myg37.com/forums/showpost.php?p=4142458&postcount=28
Last edited by Rochester; 10-22-2018 at 02:00 PM.
#20
Administrator
Thread Starter
iTrader: (9)
Red Rocket!
Funny how much smaller it seems in your hands.
Funny how much smaller it seems in your hands.
Last edited by Rochester; 10-22-2018 at 02:06 PM.
Thread
Thread Starter
Forum
Replies
Last Post
MKG37S
Engine, Drivetrain & Forced-Induction
3
02-06-2023 04:11 PM
Omstr818
General Tech Questions
5
08-11-2016 02:13 PM
deathtrap
Private Classifieds
4
07-27-2015 07:24 AM