Feedback needed for front control arms and maybe rear kits
#1
Premier Member
Thread Starter
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
Feedback needed for front control arms and maybe rear kits
Ok guys, SPC is working on the front control arms for the G37. They test fitted a mock up they had on Monday. They want feedback from you guys though on what you are looking for in a front control arm. Amount of positive or negative camber/caster? Numbers would helpful if you could post them up for me. For the 4WAS people, they have been told that the rear should fit the 4WAS systems but I told them that Max said that they were a little short. They said they might look at this in the future or have Eibach do the measurements again since they have someone with a 4WAS car. They want to get the front control arms out first because they are getting a lot of request for it and they said it is suppose to work for the 4WAS too. Any good suggestions? Give me the feedback so I can get it to them so they can look into doing it for the current system they are building. Any feedback on the rear would be welcome too. This will be stickied for a little bit to get the most feedback.
#4
Super Moderator w/ Boost
iTrader: (3)
WoW... this thread is a back track... You had posted a long time ago that SPC had already gotten the measurements from Eibach... I figure the New Camber kits would be out already... We must not be a priority... hmmm....
Tell them to Call Sharif at Forged... He was the one who explained to me about the kit not fitting... He has a G37 on Stechs... so He can give them all the feedback they can handle....
bboy... what exactly are they for sure making now? anything?
Tell them to Call Sharif at Forged... He was the one who explained to me about the kit not fitting... He has a G37 on Stechs... so He can give them all the feedback they can handle....
bboy... what exactly are they for sure making now? anything?
#6
Premier Member
Thread Starter
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
WoW... this thread is a back track... You had posted a long time ago that SPC had already gotten the measurements from Eibach... I figure the New Camber kits would be out already... We must not be a priority... hmmm....
Tell them to Call Sharif at Forged... He was the one who explained to me about the kit not fitting... He has a G37 on Stechs... so He can give them all the feedback they can handle....
bboy... what exactly are they for sure making now? anything?
Tell them to Call Sharif at Forged... He was the one who explained to me about the kit not fitting... He has a G37 on Stechs... so He can give them all the feedback they can handle....
bboy... what exactly are they for sure making now? anything?
Trending Topics
#9
Premier Member
Thread Starter
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
I believe these will since the 07+ sedans and the 08+ coupes have the same design from my understanding. The rear 07+ sedan rear camber/toe fit the Coupe so I believe the fronts that they are making will fit both the coupe and the sedan.
#10
I have Eibach's installed and the camber is -2.06 on the left and -1.37 on the right. Factory spec is supposed to be between -1.08 and .42. Caster and toe are within factory spec.
I'll try and scan my alignment sheet later in the week.
#14
Premier Member
Thread Starter
Join Date: Jul 2007
Location: Colorado Springs, CO
Posts: 3,346
Likes: 0
Received 3 Likes
on
3 Posts
IP37, I sent you a PM with the email address. This thread is no longer stickied. Thanks IP for your input. Anyone else that has input on how much camber adjustment they are looking for needs to post in this thread before it is to late.
Thread
Thread Starter
Forum
Replies
Last Post
Chris Olson
Audio, Video & Electronics
16
03-28-2024 09:46 AM