What did you do to your Sedan today?
Apr 22, 2016 | 02:17 PM
Joined: May 2015
Posts: 1,741
Likes: 358
From: Baltimore/Sykesville
Quote:
Originally Posted by
Rochester
What are you saying... that if I get the black Z1 under-shroud, its going to have silver scrapes all over it?
I'm not saying
YOU will. Just if
I had a black one, it would. That said, I don't do cartwheels pulling into my drive...
Sean
Apr 22, 2016 | 02:23 PM
Apr 22, 2016 | 02:51 PM
Joined: Sep 2015
Posts: 1,705
Likes: 341
From: Franklin Park, NJ
Quote:
Originally Posted by
VIVID
For those of you who've installed the drain valves, did you use one of the copper-crush washers on it like you would for the regular drain plug?
Apr 22, 2016 | 04:40 PM
Joined: May 2015
Posts: 1,741
Likes: 358
From: Baltimore/Sykesville
Quote:
Originally Posted by
ZahyMatar
For those of you who've installed the drain valves, did you use one of the copper-crush washers on it like you would for the regular drain plug?
IIRC, the Fumoto came with a washer so that's the one that was used.
Sean
Apr 22, 2016 | 06:06 PM
Joined: Feb 2016
Posts: 763
Likes: 140
From: Earths toilet: Houston Texas
Changed my drive belt....!
Last edited by G37sGraphite; Apr 22, 2016 at 06:12 PM .
Apr 22, 2016 | 06:10 PM
Joined: Feb 2016
Posts: 763
Likes: 140
From: Earths toilet: Houston Texas
Quote:
Originally Posted by
kennyz424
I replaced mine with this...
Please excuse all the finger prints on it lol
That is cool! I checked Z Speed and could not find it...I dont think they make it for the coupe. How much did you pay for that?
Apr 22, 2016 | 06:11 PM
Joined: Mar 2016
Posts: 3,050
Likes: 547
Swifts arrived hope to install tomorrow
Apr 22, 2016 | 06:49 PM
Joined: Sep 2015
Posts: 69
Likes: 3
Apr 22, 2016 | 06:58 PM
Joined: Apr 2015
Posts: 718
Likes: 152
From: Orange County, NY
Quote:
Originally Posted by
Bennyjoel
Tips came out great. Congrats on the new ride.
Apr 22, 2016 | 07:36 PM
Joined: Mar 2016
Posts: 3,050
Likes: 547
Also inatalled my ebay radio and climate *****.
Apr 22, 2016 | 08:07 PM
Joined: Nov 2009
Posts: 24,876
Likes: 4,949
Quote:
Originally Posted by
PNW_IPL
Also inatalled my ebay radio and climate *****.
I got the same ones, had to add some teflon tape over the control stocks so the ***** would fit tighter, but other than that they've been good.
Apr 22, 2016 | 08:57 PM
Joined: Nov 2015
Posts: 70
Likes: 12
From: central fl
That's on the list kenny how about a group buy on that
Apr 22, 2016 | 08:58 PM
Joined: Sep 2015
Posts: 263
Likes: 33
From: Temple, PA
Spent a few hours trying to get demon bolt number 2 off before putting it all back together and calling a shop for pricing.
Apr 22, 2016 | 10:14 PM
Joined: Nov 2009
Posts: 24,876
Likes: 4,949
Quote:
Originally Posted by
the_wolff
Spent a few hours trying to get demon bolt number 2 off before putting it all back together and calling a shop for pricing.
Did you try the ATF/Acetone rust removing cocktail, if not give it a shot (unless the bolt's already rounded)
Apr 23, 2016 | 09:58 AM
Joined: Mar 2016
Posts: 161
Likes: 20
From: Rochester, NY
Quote:
Originally Posted by
blnewt
I got the same ones, had to add some teflon tape over the control stocks so the ***** would fit tighter, but other than that they've been good.
I had the same issue. 3 fit perfect. 2 were a little too big. I put a small piece of electrical tape through the slit of the bottom right stem (I'll never touch that one) left the ends hanging out to take up the extra space, pressed the **** on, all good.
The wife, who is getting jealous of the G, was enjoying telling everyone at a party last night to go check out my *****.
