ECU Tuning / Dyno Data This subforum is specifically aimed at ECU Tuning reviews, questions, dyno charts, etc..

BBOY's Dynos of his stock G37

Thread Tools
 
Search this Thread
 
Old Mar 9, 2008 | 08:04 PM
  #1  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
15 Year Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
BBOY's Dynos of his stock G37

Here are the dynos I got of my stock G37. Did this so I know what my numbers will be before my upgrades so I know what I get after each upgrade.

Enjoy:

Stock G37 Best of the first three runs 4th gear at 4k RPM:



Stock G37 three runs together:



Stock G37 max run (4th run) at 3k RPM:



Stock G37 Max number compared to previous three runs:



That is all the dynos I got.
Reply
Old Mar 9, 2008 | 08:30 PM
  #2  
Kidcane's Avatar
Kidcane
Florida G Club
iTrader: (7)
 
Joined: Dec 2005
Posts: 8,105
Likes: 9
From: Tampa
Cool. What kind of dyno was it?
Reply
Old Mar 9, 2008 | 08:33 PM
  #3  
MaxToTheG37's Avatar
MaxToTheG37
Super Moderator w/ Boost
iTrader: (3)
 
Joined: Dec 2007
Posts: 7,042
Likes: 5
From: Knoxville TN
Good Job!!!
Reply
Old Mar 9, 2008 | 08:43 PM
  #4  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
15 Year Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Originally Posted by Kidcane
Cool. What kind of dyno was it?
To be honest, I don't know. It was the type were you roll the rear wheels over two drums that measure the HP/TQ. I guess you have to tie down the cat as well. Hopefully some dyno experts can let us know. I was hoping the type would be on the bottom of the page but I am not sure if that is the type or not.
Reply
Old Mar 9, 2008 | 11:30 PM
  #5  
solopresident's Avatar
solopresident
Premier Member
 
Joined: Feb 2007
Posts: 3,478
Likes: 1
From: So. Cal
dont they normally do pulls in 3rd gear?
Reply
Old Mar 9, 2008 | 11:36 PM
  #6  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
15 Year Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Originally Posted by solopresident
dont they normally do pulls in 3rd gear?
You got me. The guy asked me which gear was 1:1 but I didn't know. He figured it was 3rd or 4th. I assume he found out 4th was 1:1. I never looked it up after.
Reply
Old Mar 9, 2008 | 11:38 PM
  #7  
NemesisG37's Avatar
NemesisG37
Registered User
 
Joined: Oct 2007
Posts: 608
Likes: 1
From: Tarzana CA
looks way too low.
Reply
Old Mar 9, 2008 | 11:40 PM
  #8  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
15 Year Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
hmm...Just looked it up.

It looks like the 5th gear is the 1:1 ratio in the 6spd whereas the auto is 4th.

Drivetrain : Rear-Wheel Drive
Trans Type : 6
Trans Description Cont. : Manual w/OD
First Gear Ratio (:1) : 3.79
Second Gear Ratio (:1) : 2.32
Third Gear Ratio (:1) : 1.62
Fourth Gear Rato (:1) : 1.27
Fifth Gear Ratio (:1) : 1.00
Sixth Gear Ratio (:1) : 0.79
Reverse Ratio (:1) : 3.45
Final Drive Axle Ratio (:1) : 3.69
Reply
Old Mar 9, 2008 | 11:46 PM
  #9  
NemesisG37's Avatar
NemesisG37
Registered User
 
Joined: Oct 2007
Posts: 608
Likes: 1
From: Tarzana CA
well that explains everything. You should ask to re dyno it...or else youll have to keep dynoing it in 4th if you want to know what gains your mods make
Reply
Old Mar 10, 2008 | 12:11 AM
  #10  
GiGGaplease's Avatar
GiGGaplease
Registered User
 
Joined: Jul 2007
Posts: 6,301
Likes: 1
From: al, eguor notab
Originally Posted by NemesisG37
looks way too low.
agree, shouldnt it be around 260?
Reply
Old Mar 10, 2008 | 02:08 AM
  #11  
majin ssj eric's Avatar
majin ssj eric
Registered User
 
Joined: Jan 2008
Posts: 1,213
Likes: 2
From: Saint Simons Island, GA
At the usual drivetrain loss of 15%, 330 hp at the crank should come out to 280hp at the rear wheel. What is up with this VQ motor? Is it overrated?
Reply
Old Mar 10, 2008 | 02:36 AM
  #12  
cvt's Avatar
cvt
Registered User
 
Joined: Apr 2006
Posts: 1,499
Likes: 8
From: Los Angeles
Originally Posted by majin ssj eric
At the usual drivetrain loss of 15%, 330 hp at the crank should come out to 280hp at the rear wheel. What is up with this VQ motor? Is it overrated?
well first of all it looks like he dyno'd at the wrong gear...and secondly it looks like a "suprflow" dyno..which reads considerably lower than a dynojet or a dynapack.

there have been guys here who have dyoned between 270-290whp and 302hp at the hub...

there is nothing "up" with this VQ motor...different kinds of dynos read differently
Reply
Old Mar 10, 2008 | 03:09 AM
  #13  
gsazabi's Avatar
gsazabi
Registered User
 
Joined: Sep 2005
Posts: 48
Likes: 0
Super Flow Dynamometer reads SUPER low. If you want dynamometer that'll put smile on your face, go dyno on Dynapack lol
Reply
Old Mar 10, 2008 | 09:00 AM
  #14  
UltimateGee27's Avatar
UltimateGee27
Registered User
 
Joined: Jan 2007
Posts: 154
Likes: 2
From: FtLauderdale Fl
yea those numbers are off....either wrong gear pull or a weird dyno machine.....the 3.7 should pull alot higher than that.
Reply
Old Mar 10, 2008 | 12:41 PM
  #15  
brown_fv's Avatar
brown_fv
Registered User
 
Joined: Mar 2007
Posts: 2
Likes: 0
From: Toronto (GTA), ON, Canada
Dyno chart says superflow dyno...they read mad low dont they?
Reply



All times are GMT -4. The time now is 02:33 AM.