HID Clips Secure
#1
HID Clips Secure
Guys I neglected to post this with my Phillips 6000k thread BUT when I did the install the small square washer on each screw fell down into the housing and could not be retrieved.
So my question is, did this happen to anyone else? Any concerns with the washers helping secure the U-shaped clip in the locked position or does the screw pretty much hold in tight?
I've noticed more headlight flicker on the drivers side (ever since eibach) when I hit bumps and I fear that perhaps the clip isn't secure without the washer.
Thanks!
https://www.myg37.com/forums/body-in...ial-price.html
So my question is, did this happen to anyone else? Any concerns with the washers helping secure the U-shaped clip in the locked position or does the screw pretty much hold in tight?
I've noticed more headlight flicker on the drivers side (ever since eibach) when I hit bumps and I fear that perhaps the clip isn't secure without the washer.
Thanks!
https://www.myg37.com/forums/body-in...ial-price.html
Last edited by DrJones; 02-07-2009 at 11:32 PM.
#4
Florida G35 Club, Premier Member
iTrader: (3)
Join Date: Oct 2005
Location: Orlando, FL
Posts: 2,508
Likes: 0
Received 0 Likes
on
0 Posts
I dropped a little thing in there too. I was following the DIY on here for the passenger side, but then i realized that you dont need to unscrew anything for the bulb removal at all!!
I was pissed... But yeah, it was a while back, and no problems yet.
I was pissed... But yeah, it was a while back, and no problems yet.
#6
^ Yep... after you unplug the silver "power" box from the base of the light there is that small screw at the top of the housing. I unscrewed it (it said so in the DIY) but a small washer fell down into the housing.... no way to get it even with a magnet... I was under the impression that the washer held the U shaped clip snug to the housing.
Trending Topics
#8
Registered User
iTrader: (1)
Join Date: Apr 2006
Location: jacksonville, fl
Posts: 4,563
Likes: 0
Received 0 Likes
on
0 Posts
the silver box is the ignitor. id have to take my light apart to figure out what you did sorry but you might just try making sure your ignitor is turned so it locks/snaps completely. if that washer is needed to hold it snug, just get 1 from home depot?
#9
Registered User
iTrader: (10)
^ Yep... after you unplug the silver "power" box from the base of the light there is that small screw at the top of the housing. I unscrewed it (it said so in the DIY) but a small washer fell down into the housing.... no way to get it even with a magnet... I was under the impression that the washer held the U shaped clip snug to the housing.
yeah. that didn't had to be removed, it was just a push release kind of clip to secure the bulb.
i have a extra one if you need it! screws and clip. maybe i could just stuck it in one of those big envelopes and send it off to you if you need it. no charge!
#10
Registered User
Join Date: Sep 2005
Location: Augusta, GA
Posts: 1,664
Likes: 0
Received 0 Likes
on
0 Posts
i did the same thing with the first bulb i changed. ended up taking the bumper off to get the headlight off to get it out
then i looked closer and realized i didn't have to unscrew anything and felt stupid
you just need to squeeze the metal clip that's on the back of the bulb if i remember right
then i looked closer and realized i didn't have to unscrew anything and felt stupid
you just need to squeeze the metal clip that's on the back of the bulb if i remember right
#12
So I didn't have you remove the screw... damn! By the looks of it the gold washer holds the top of the clip in place. without the washer it stands to reason that the clip can come open and the light fall out of place.
Am I right or wrong? Going to go pick up two of them from the Depot or something. Weiboy can you give me an idea of the measurement for ea. ?
Thanks!
Am I right or wrong? Going to go pick up two of them from the Depot or something. Weiboy can you give me an idea of the measurement for ea. ?
Thanks!
Last edited by DrJones; 02-08-2009 at 09:39 PM.
#13
Registered User
iTrader: (10)
So I didn't have you remove the screw... damn! By the looks of it the gold washer holds the top of the clip in place. without the washer it stands to reason that the clip can come open and the light fall out of place.
Am I right or wrong? Going to go pick up two of them from the Depot or something. Weiboy can you give me an idea of the measurement for ea. ?
Thanks!
Am I right or wrong? Going to go pick up two of them from the Depot or something. Weiboy can you give me an idea of the measurement for ea. ?
Thanks!
Thread
Thread Starter
Forum
Replies
Last Post
blnewt
D.I.Y. Installations/Modifications
37
10-17-2020 11:12 AM
2012G37
Brakes & Suspension
36
06-03-2018 06:59 PM
dedmanchan
Audio, Video & Electronics
1
09-24-2015 11:25 PM