Any VA G37's?
probably sunday would be best for me. I'm gonna figure out later today if i have enough time to drive down with the crap i gotta do today.
I painted my grill a few weeks ago, its not too difficult. Theres a DIY on here somewhere, just gotta sand down, prime, and paint. I don't have any chips so far. Other than on the Mt. Fuji, the paint didn't stick well to that and its chipped a little.
I got my headlights out today. Took about an hour for me to do and I didn't have to remove the entire bumper.
But I can't begin to tell you how much of a pain in the *** it is to do. I'm sure when it's time to re-assemble, it won't be as bad, but man it sucked to do this morning.
But I can't begin to tell you how much of a pain in the *** it is to do. I'm sure when it's time to re-assemble, it won't be as bad, but man it sucked to do this morning.
Registered Member
Joined: Dec 2010
Posts: 249
Likes: 1
From: Williamsburg, VA
I got my headlights out today. Took about an hour for me to do and I didn't have to remove the entire bumper.
But I can't begin to tell you how much of a pain in the *** it is to do. I'm sure when it's time to re-assemble, it won't be as bad, but man it sucked to do this morning.
But I can't begin to tell you how much of a pain in the *** it is to do. I'm sure when it's time to re-assemble, it won't be as bad, but man it sucked to do this morning.
Yea, Ozzie from NGC was gonna be down in Norfold to pick up Bryants headlights so i figured i was a good pitstop on his trip. It was too good of a price,came and picked them up, and will deliver them back to me too...can't pass that up. Bryants are gonna look way cooler than mine anyway-his wife lets him spend more money than my girl haha 
Doing headlights is a BISHhhhhh
I don't know why these lights are so effing difficult to take out. My friends Audi had 3 screws and it slid right out, we baked it swapped the lenses and put that sucker back in within a couple hours.
It took me 2 hours or so to get my lights out last time and 2 weeks to bake open paint and swap lenses hahah (I got fed up and left them in my kitchen for a week and a half)
The worst part is I have to redo them because one of them has condensation. USE RUBBER BUTYL TAPE!
If you are local I can give you some. I used it on one side, got lazy didn't use it on the other side. sure enough the side with butyl is fine the other side looks like my shower mirror after a hot one.
I don't know why these lights are so effing difficult to take out. My friends Audi had 3 screws and it slid right out, we baked it swapped the lenses and put that sucker back in within a couple hours.
It took me 2 hours or so to get my lights out last time and 2 weeks to bake open paint and swap lenses hahah (I got fed up and left them in my kitchen for a week and a half)
The worst part is I have to redo them because one of them has condensation. USE RUBBER BUTYL TAPE!
If you are local I can give you some. I used it on one side, got lazy didn't use it on the other side. sure enough the side with butyl is fine the other side looks like my shower mirror after a hot one.
Doing headlights is a BISHhhhhh
I don't know why these lights are so effing difficult to take out. My friends Audi had 3 screws and it slid right out, we baked it swapped the lenses and put that sucker back in within a couple hours.
It took me 2 hours or so to get my lights out last time and 2 weeks to bake open paint and swap lenses hahah (I got fed up and left them in my kitchen for a week and a half)
The worst part is I have to redo them because one of them has condensation. USE RUBBER BUTYL TAPE!
If you are local I can give you some. I used it on one side, got lazy didn't use it on the other side. sure enough the side with butyl is fine the other side looks like my shower mirror after a hot one.
I don't know why these lights are so effing difficult to take out. My friends Audi had 3 screws and it slid right out, we baked it swapped the lenses and put that sucker back in within a couple hours.
It took me 2 hours or so to get my lights out last time and 2 weeks to bake open paint and swap lenses hahah (I got fed up and left them in my kitchen for a week and a half)
The worst part is I have to redo them because one of them has condensation. USE RUBBER BUTYL TAPE!
If you are local I can give you some. I used it on one side, got lazy didn't use it on the other side. sure enough the side with butyl is fine the other side looks like my shower mirror after a hot one.
