MODDING 411 Aftermarket Parts Available for the G37: What's Good, What's Not, Where to Go etc.

Pics of Spring Mods needed

Old Apr 17, 2008 | 01:43 AM
  #1  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Pics of Spring Mods needed

I need a couple pics of each spring mod to add to the Modding Section. Anyone that has the H&R or Eibach, get me a pic of the side of the car showing the drop. Scheme has some good pics but I cannot link to them. If someone can host the pics on their photobucket (or something else) account that would be helpful. It was suggested that it would be helpful if there were pictures of the drop for each spring added to the Suspension section which I am trying to do.

If anyone knows of anyother springs out for the G37 besides these two then let me know and give me links to the site for the product.
Reply
Old Apr 17, 2008 | 02:01 AM
  #2  
gmlee86's Avatar
gmlee86
Registered Member
iTrader: (1)
 
Joined: Nov 2007
Posts: 1,687
Likes: 2
From: So. Cal
Pics inside

https://www.myg37.com/forums/brakes-and-suspension/177426-tanabe-nf210-installed-with-pics.html
Reply
Old Apr 17, 2008 | 02:22 AM
  #3  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Originally Posted by gmlee86
Hey gmlee86, can you take another pic of the side of your car but closer up. Like the your pic here:


but much closer?
Reply
Old Apr 17, 2008 | 02:46 AM
  #4  
gmlee86's Avatar
gmlee86
Registered Member
iTrader: (1)
 
Joined: Nov 2007
Posts: 1,687
Likes: 2
From: So. Cal
Eventually
Reply
Old Apr 17, 2008 | 07:38 AM
  #5  
IP37's Avatar
IP37
Registered User
 
Joined: Sep 2005
Posts: 1,664
Likes: 0
From: Augusta, GA
h&r springs..


Reply
Old Apr 17, 2008 | 02:32 PM
  #6  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Thanks IP37
Reply
Old Apr 18, 2008 | 02:43 AM
  #7  
HER37S's Avatar
HER37S
Registered User
 
Joined: Nov 2007
Posts: 215
Likes: 0
From: Tucson AZ
TEIN S.Techs

Springs are the TEIN S.Techs. I should have my new Volks on next week; I’ll do the pics over with the 20" GT 30s installed








Reply
Old Apr 18, 2008 | 03:25 AM
  #8  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Thanks Lady.
Reply
Old Apr 18, 2008 | 08:40 AM
  #9  
HER37S's Avatar
HER37S
Registered User
 
Joined: Nov 2007
Posts: 215
Likes: 0
From: Tucson AZ
No problem, thank you for putting together this great MODDING 411 Sticky
Reply
Old Apr 18, 2008 | 08:55 AM
  #10  
IP37's Avatar
IP37
Registered User
 
Joined: Sep 2005
Posts: 1,664
Likes: 0
From: Augusta, GA
think the information on the h&r springs is wrong on your page..
the h&r site says approx 1.5" front, approx 1.4" rear

also if you want, you could add that the part number on the actual springs is the same part number as the 350z springs
Reply
Old Apr 18, 2008 | 02:55 PM
  #11  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Originally Posted by IP37
think the information on the h&r springs is wrong on your page..
the h&r site says approx 1.5" front, approx 1.4" rear

also if you want, you could add that the part number on the actual springs is the same part number as the 350z springs
Can you put the link to them here? I pulled the info from their site so unless I pulled it off the wrong springs it should be right. The info I used should can be seen if you follow the H&R site link in the post. Let me know if I did the wrong springs and what the correct link it. Please.
Reply
Old Apr 18, 2008 | 03:14 PM
  #12  
IP37's Avatar
IP37
Registered User
 
Joined: Sep 2005
Posts: 1,664
Likes: 0
From: Augusta, GA
you have the right link.. the part number for the set of springs for each car is different, but if you look at the actual springs themselves, they have the same part number on them

unless they've been boxing them wrong
Reply
Old Apr 18, 2008 | 07:45 PM
  #13  
TerribleONE453's Avatar
TerribleONE453
Registered User
 
Joined: Oct 2007
Posts: 4,404
Likes: 5
From: Chatsworth CA
weird... im thinking that may be the case for me because my springs seem a bit soft and since our car is much heavier that makes sense. btw IP your car looks amazing in that second picture
Reply
Old Apr 27, 2008 | 02:33 PM
  #14  
bboysteele's Avatar
bboysteele
Thread Starter
Premier Member
 
Joined: Jul 2007
Posts: 3,346
Likes: 3
From: Colorado Springs, CO
Still need pics of a car with the Eibach Pro-Kit lowering springs and the TEIN H-TECH Springs.
Reply
Old Apr 27, 2008 | 03:28 PM
  #15  
gmlee86's Avatar
gmlee86
Registered Member
iTrader: (1)
 
Joined: Nov 2007
Posts: 1,687
Likes: 2
From: So. Cal
gan78mao is the only person you'll be able to get the Pro Kit pics from for what seems like will be a long time with all the delays
Reply

Thread Tools
Search this Thread

All times are GMT -4. The time now is 07:18 PM.