Mark this thread as Unsold
WTB WTB: Paddle Shifter Kit
Thread Starter
Registered Member
iTrader: (2)
Joined: Dec 2016
Posts: 477
Likes: 80
From: Garner, N.C.
WTB: Trim & HDWR for Paddle Shifters (Black)
Category: Accessories
Price: $123456789
Private or Vendor Listing: Private Listing
Part fits: 2010+ G37 Coupe, 2010+ G37 Sedan
Location (State/Prov): NC
Item Condition: Used
Black is preferred, but open for whatever you have.
So... who has any of this available?
Update......
Scored the Paddle Shifters off Ebay, so now I only need the Black Trim and HDWR.
Last edited by The Pope; May 17, 2018 at 04:50 PM. Reason: added color preferance
Registered Member
Joined: Jan 2017
Posts: 228
Likes: 38
From: Trinity, FL
Don't have one for sale, but it would help if in your quest to find one if you list what color you need. Black or Stone. I have the stone and it was easier for me to buy the shroud at Infiniti of Gwinnett and I picked up some used paddles on ebay for a decent price. I'd say total was around $200 I spent. Good luck in your search!
Thread Starter
Registered Member
iTrader: (2)
Joined: Dec 2016
Posts: 477
Likes: 80
From: Garner, N.C.
Don't have one for sale, but it would help if in your quest to find one if you list what color you need. Black or Stone. I have the stone and it was easier for me to buy the shroud at Infiniti of Gwinnett and I picked up some used paddles on ebay for a decent price. I'd say total was around $200 I spent. Good luck in your search!
Thanks QDE for pointing that out!
Thread Starter
Registered Member
iTrader: (2)
Joined: Dec 2016
Posts: 477
Likes: 80
From: Garner, N.C.
I just checked out the shroud on my car and it has what looks like removable tabs in it where the paddles go!
So am I correct in thinking that I don't need to get another shroud?
Sorry for the rotated cellphone photo!
So am I correct in thinking that I don't need to get another shroud?
Sorry for the rotated cellphone photo!
Trending Topics
Registered Member
Joined: Jan 2017
Posts: 228
Likes: 38
From: Trinity, FL
Infiniti of Gwinnett. This is what you need, they ship.
https://m.ebay.com/itm/Shroud-for-In...0AAOSwKGpa6hrN
https://m.ebay.com/itm/Shroud-for-In...0AAOSwKGpa6hrN
Thread Starter
Registered Member
iTrader: (2)
Joined: Dec 2016
Posts: 477
Likes: 80
From: Garner, N.C.
^ Yes, I've got that on my Ebay Watch List. Just seeing if I can locate it for less. Thanks for posting.
^^ I'll have less than $300 in this if I get the trim that QDE posted. Tell your friend, GLWS. (no sarcasm intended)
^^ I'll have less than $300 in this if I get the trim that QDE posted. Tell your friend, GLWS. (no sarcasm intended)
Thread Starter
Registered Member
iTrader: (2)
Joined: Dec 2016
Posts: 477
Likes: 80
From: Garner, N.C.
I've got another question about the shroud......
Is the only difference between lower half of a non-paddle and paddled shrouds just the two cutouts and the access panel to clear the paddles and the upper halfs are the same?
Is the only difference between lower half of a non-paddle and paddled shrouds just the two cutouts and the access panel to clear the paddles and the upper halfs are the same?
Last edited by The Pope; May 22, 2018 at 03:45 PM.
Registered Member
Joined: Jan 2018
Posts: 32
Likes: 2
From: New Jersey
The non paddle shroud comes in 2 pieces while the paddled shroud comes in 4 pieces. The bottom panel is smaller than the original and the top part is sperated into parts on each respective sides and a single top section. You can reuse the top piece as this is what I did because of the fabric trim attached to it. Hopefully this answers your question
This is a write up I found from a different forum that might help.
http://www.infinitig37.com/infiniti-...r-install.html
Last edited by Revy; May 22, 2018 at 04:58 PM.