Status Elite Intakes
03-11-2009, 04:48 AM
#31
Former Sponsor
iTrader: (1)
Join Date: Dec 2008
Location: Danville, CA
Posts: 267
Likes: 0
Received 0 Likes
on
0 Posts
Thank you for all your interest guys sorry to respond late, I didnt catch this thread. We will be test fitting intakes on a 07+ G35 sedan. These intakes will work on a 370z with minor modification which we are undergoing.
Status Elite Velocity Stacked Intake
S E Velocity Stacked Intakes are designed for maximum airflow. It is a fully polished T6-6061 light weight aluminum piping that starts at the throttle body to enhance airflow consistency. Piping is then mated to a velocity stack utilizing TurboHoses™ AirRam race-proven technology to increase airflow speed. The high quality SE Turbo Filter’s aluminum mesh filtration design allows up to 5 microns. This remarkable design incorporates another filtration system at the top of its filter aimed inches from at the factory air ducts for direct airflow when rolling. That’s not all. The inside of the SE Filter is cone-shaped, allowing the airflow to swirl as it enters the velocity stack. This high performance design truly maximizes airflow. Status Elite products stresses on high quality with maximum performance. Each intake is hand crafted and welded 100% in the USA.
Status Elite Velocity Stacked Intake
S E Velocity Stacked Intakes are designed for maximum airflow. It is a fully polished T6-6061 light weight aluminum piping that starts at the throttle body to enhance airflow consistency. Piping is then mated to a velocity stack utilizing TurboHoses™ AirRam race-proven technology to increase airflow speed. The high quality SE Turbo Filter’s aluminum mesh filtration design allows up to 5 microns. This remarkable design incorporates another filtration system at the top of its filter aimed inches from at the factory air ducts for direct airflow when rolling. That’s not all. The inside of the SE Filter is cone-shaped, allowing the airflow to swirl as it enters the velocity stack. This high performance design truly maximizes airflow. Status Elite products stresses on high quality with maximum performance. Each intake is hand crafted and welded 100% in the USA.
03-11-2009, 05:04 AM
#32
Former Sponsor
iTrader: (1)
Join Date: Dec 2008
Location: Danville, CA
Posts: 267
Likes: 0
Received 0 Likes
on
0 Posts
This has got to be the highest quality and performance intake available to for the G37. The workmanship is excellent. We have spent six months designing and finalizing this intake. Custom designed CNC Mass Airflow Sensor Blocks were prodiced. Compare those to every other intake manufacture for the G37. We may offer a carbon heat shield in the future at an accessory. There are not many performance upgrades for the G37, and there will never be as many available as a turbocharged car, so pick up a high quality intake, afterall what other performance products do you have to show off in your engine bay?
Kevin
Kevin
03-11-2009, 10:08 PM
#35
Registered User
Join Date: Aug 2008
Location: Clifton Park, NY and NYC
Posts: 1,153
Likes: 0
Received 0 Likes
on
0 Posts
03-12-2009, 03:48 AM
#36
Former Sponsor
iTrader: (1)
Join Date: Dec 2008
Location: Danville, CA
Posts: 267
Likes: 0
Received 0 Likes
on
0 Posts
Yes, each intake is very very nicely hand made, welded, and powdercoated carefully!
These are about the largest filters you can fit in the engine bay. Check out the clearances of the filter!
Don't worry there are no clearance issues! Direct bolt on. No dremeling needed. One piece tube for bling and easy install.
03-12-2009, 05:16 AM
#42
Fujita's don't have big velocity stacks like the status elites or the JWT'S.
They also offer custom powder coats plus the bigger filters that should help on the air flow.
Heat shields should help. Please convince status elite for our G community
WhiteG37S can you make some with carbon fiber pipes?
Thats what i said to them too
That would look sexy for sure
They also offer custom powder coats plus the bigger filters that should help on the air flow.
Heat shields should help. Please convince status elite for our G community
WhiteG37S can you make some with carbon fiber pipes?
Thats what i said to them too
That would look sexy for sureHow much more for custom colors?
and will these be compatible with the GT Spec strut bars?
I can't tell from the pictures.
03-12-2009, 05:33 AM
#44
Registered User
Join Date: Jul 2008
Location: Midland, Texas. The Desert
Posts: 113
Likes: 0
Received 0 Likes
on
0 Posts
