Official Low Offset/Hellaflush Thread
#1982
But Your running 9.5 ? In the front with what offset ?
Just wondering you think 10.5 would fit like the back does up front? Or I'd have to mess with fender rolling Wich isint an issue just need some pointers I'm used to modding civics where nothing really fits lol
#1983
Registered Member
iTrader: (1)
front were +12 and rears +22
IF your planning on going as low as me then yes you need cambers, it wont fit lol
And if you don't use camber then you will need major fender roll
And you can only pull so much before fenders start flaring, but its all up 2 the driver lol
flares are FTL lol
And also remember im driving a sedan not a coupe lol I habe smaller gap too
IF your planning on going as low as me then yes you need cambers, it wont fit lol
And if you don't use camber then you will need major fender roll
And you can only pull so much before fenders start flaring, but its all up 2 the driver lol
flares are FTL lol
And also remember im driving a sedan not a coupe lol I habe smaller gap too
#1984
front were +12 and rears +22
IF your planning on going as low as me then yes you need cambers, it wont fit lol
And if you don't use camber then you will need major fender roll
And you can only pull so much before fenders start flaring, but its all up 2 the driver lol
flares are FTL lol
And also remember im driving a sedan not a coupe lol I habe smaller gap too
IF your planning on going as low as me then yes you need cambers, it wont fit lol
And if you don't use camber then you will need major fender roll
And you can only pull so much before fenders start flaring, but its all up 2 the driver lol
flares are FTL lol
And also remember im driving a sedan not a coupe lol I habe smaller gap too
you didnt need the camber kit in the front did you?
lol yeah i dont want my fenders looking like crap im trying to minimize body work on the car..
yeah mines a sedan too. but these socal streets are a pain in the a** sometimes. lol
The following users liked this post:
Nappy_G (05-21-2015)
#1986
Thats what im getting stance coils just didnt order the camber arms my buddy was telling me i wasnt really going to need it for the rear and he's running 20x10 front and 20x11 rear
But Your running 9.5 ? In the front with what offset ?
Just wondering you think 10.5 would fit like the back does up front? Or I'd have to mess with fender rolling Wich isint an issue just need some pointers I'm used to modding civics where nothing really fits lol
But Your running 9.5 ? In the front with what offset ?
Just wondering you think 10.5 would fit like the back does up front? Or I'd have to mess with fender rolling Wich isint an issue just need some pointers I'm used to modding civics where nothing really fits lol
#1989
but he had to do some minor pulling on his quarters i cant really remeber his specs.
sorry typo i ment +35
Last edited by Nappy_G; 05-21-2015 at 07:26 PM.
The following users liked this post:
pgG37 (05-21-2015)
The following users liked this post:
b-drizzy (05-22-2015)
#1994
Good mornin' every1. Quick question. Getting Vossens install today....wondering if it would require a fender pull. Getting the vfs2 satin bronze in 20x9+32 and 20x10.5 +45 with 245/35/20 & 275/30/20 . With stance coilovers & spc F + R camber kit. Can I go 25.75" or 26" all around or how low b4 fender pull required?