Mark this thread as Unsold
Parts Search
Keyword:

Category:

Price:

Private or Vendor Listing:

Location (State/Prov):



Cars Search
Keyword:

Year:
(Range)

Make:

Model:

Price:

Mileage:

Color:

Private or Dealer Listing:

Location (State/Prov):

FS MRP 2.75" OD 2.5" ID screen billet MAF housing

Thread Tools
 
Search this Thread
 
Old 06-17-2019, 09:48 PM
  #1  
4doorfury
Registered User
Thread Starter
iTrader: (1)
 
4doorfury's Avatar
 
Join Date: May 2016
Location: Tampa, FL
Posts: 680
Received 75 Likes on 58 Posts
MRP 2.75" OD 2.5" ID screen billet MAF housing

Category: Engine - Intake/Fuel
Price: $120
Private or Vendor Listing: Private Listing
Part fits: 2010+ G37 Coupe, 2010+ G37 Sedan, 2008-2009 G37 Coupe, 2008-2009 G37 Sedan
Location (State/Prov): FL
Item Condition: Used

I used these on my custom short ram setup and made good power. Pre tune I was 317whp with muffler delete. These things cost almost $200 new. I switched to 3" long tube and so far have not seen any gains comparing both intakes tuned on ecutek. Selling only because I have no use for 2 intakes.
4doorfury is offline  
Old 06-18-2019, 02:11 PM
  #2  
rotarymike
Moderator in Moderation
iTrader: (4)
 
rotarymike's Avatar
 
Join Date: Feb 2017
Location: Charleston
Posts: 2,537
Received 449 Likes on 377 Posts
is the 2.5: ID the same as oem?
rotarymike is offline  
Old 06-18-2019, 05:02 PM
  #3  
4doorfury
Registered User
Thread Starter
iTrader: (1)
 
4doorfury's Avatar
 
Join Date: May 2016
Location: Tampa, FL
Posts: 680
Received 75 Likes on 58 Posts
OEM are approx 2.4" ID so these will be slightly larger causing it to lean out somewhat with the OEM tune. I ran it with HFC, exhaust and ported upper/lower plenums and would see low 13s wide open throttle and the normal 14.7 cruising.
4doorfury is offline  
Old 06-19-2019, 02:58 PM
  #4  
rotarymike
Moderator in Moderation
iTrader: (4)
 
rotarymike's Avatar
 
Join Date: Feb 2017
Location: Charleston
Posts: 2,537
Received 449 Likes on 377 Posts
So tune needed eventually to see max gains, but not needed to drive to the tuning shop.

PM'ing
rotarymike is offline  
Old 06-19-2019, 04:15 PM
  #5  
4doorfury
Registered User
Thread Starter
iTrader: (1)
 
4doorfury's Avatar
 
Join Date: May 2016
Location: Tampa, FL
Posts: 680
Received 75 Likes on 58 Posts
Mine worked without a tune but occasionally I needed to reset the ecu because it would throw a MAF code. I probably drove on these for about 2 months without a tune. As always, would suggest a tune.

Replied to PMs
4doorfury is offline  
Old 06-19-2019, 06:45 PM
  #6  
4doorfury
Registered User
Thread Starter
iTrader: (1)
 
4doorfury's Avatar
 
Join Date: May 2016
Location: Tampa, FL
Posts: 680
Received 75 Likes on 58 Posts
Sold to rotarymike. Thanks bud
4doorfury is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Ali6767
Engine, Drivetrain & Forced-Induction
5
06-30-2015 05:18 PM
sobi6111
Private Classifieds
7
10-22-2010 03:52 PM
marine66
Audio/Video/Electronics
4
03-13-2010 10:23 PM



Quick Reply: FS MRP 2.75" OD 2.5" ID screen billet MAF housing



All times are GMT -4. The time now is 04:10 AM.