MyG37

MyG37 (https://www.myg37.com/forums/)
-   G37 Sedan (https://www.myg37.com/forums/g37-sedan-348/)
-   -   How to remove interior door panel? (https://www.myg37.com/forums/g37-sedan/226516-how-to-remove-interior-door-panel.html)

alex 09-15-2011 12:59 PM

How to remove interior door panel?
 
hi, everyone,
I need to replace my side view mirror on the right side of my car(2010 G37 Sedan). In order to do that, I have to remove the door panel of the right front door. So far, I've only been able to find this DIY:

https://www.myg37.com/forums/d-i-y-in...oor-panel.html

but this DIY is based on a different model. I understand the basics are the same, but are there any different bolts I have to deal with? If you have done so, could you please give me some suggestions and tips?

is Remove Tool some special tool that I have to buy? I think i can just use anything that works like it.

Thank you!

p/s: in case you wonder why i have to do this:


https://www.myg37.com/forums/g37-sed...francisco.html

rpm&my_G35 09-15-2011 01:24 PM

maybe this will help:
DIY: 2007+ Sedan Door Panel Removal - G35Driver

taken from here:
V36 DIY - G35Driver

fmr5998 09-15-2011 01:33 PM

4 Piece Nylon Pry Bar Installer Kit

These tools should work. Plastic will help prevent scratches, and they're cheap.

timmy0257 09-15-2011 02:34 PM

remove doro finisher
 
get a interior tool from autozone. i have a metal one, so i put a sock on the outside.

GXXXV X 09-15-2011 04:12 PM

you can also use a flathead screwdriver with a cloth over it :D

alex 09-15-2011 07:20 PM

Thanks to everyone!

Our G37 Sedan board is awesome! I asked this question on DIY board, and nobody had anything to say. Our board rocks!

alex 09-17-2011 06:46 PM

Hi, everyone, again!
I wanna replace part 5 from this photo:

http://farm7.static.flickr.com/6201/...0330f9dc_b.jpg

However, the plug of the mirror wire(not shown in the above photo, but is shown in the next photo) is too big to go through part 5 and part 6:

http://farm7.static.flickr.com/6177/...daeb30b5_b.jpg

guys, how do I dissemble the plug? I've tried many ways.

alex 09-18-2011 12:51 AM

ok, i figured out! Let me share it with everyone. There are about 9 pins in this harness. Each one is held by some fishhook in the harness. I used a needle tool to unhook the fishhooks to release the pins:


OBD0 ECU Pin removal - YouTube

How to remove the pin from a Buell headlight wire harness - YouTube

To assemble back, simply insert all pins back in. Make sure to write down the positions of the 9 pins before taking them out. And the pins are not upside down.

hope this helps!

rpm&my_G35 09-18-2011 09:22 AM


Originally Posted by alex (Post 3234465)
ok, i figured out! Let me share it with everyone. There are about 9 pins in this harness. Each one is held by some fishhook in the harness. I used a needle tool to unhook the fishhooks to release the pins:

To assemble back, simply insert all pins back in. Make sure to write down the positions of the 9 pins before taking them out. And the pins are not upside down.

hope this helps!

...or snap a couple pictures, like you did, so you can see which wires go where :)
...Nice video find, thanks for posting the video links. :biggthumpup:

cy7878 09-18-2011 10:49 AM

nice post, thanks

JohnnysG 04-15-2017 10:33 PM

Has anyone removed the door panel and disconnected the wiring? If so, why won't my driver side window roll up now? My passenger side works - driver side does't. I'm confused

Epiphany 04-15-2017 10:56 PM


Originally Posted by JohnnysG (Post 4125904)
Has anyone removed the door panel and disconnected the wiring? If so, why won't my driver side window roll up now? My passenger side works - driver side does't. I'm confused

Take it apart again and double check the connection in seated fully. Might not be fully connected.


All times are GMT -4. The time now is 08:36 AM.


© 2019 MH Sub I, LLC dba Internet Brands