Help with V3 Triton Installation
#1
Help with V3 Triton Installation
Hey guys, I recently purchased the Osram CBI 5K D2S bulbs, V3 Red LED Lights for the rear turn signals, V3 Switchback 5K LED turn signals, CREE MT-G2 High Power LED fog lights, 5K Vleds reverse lights, 5K license plate LEDs, and 5K City LEDs.
I was able to install the rear turn signals, license plate LEDs, and reverse LEDs.
Does the front bumper have to be removed to install the switchback V3 Triton LEDs turn signal and the Osram CBI 5K bulbs. Or is there an easier way of installing them
Any advice is appreciated.
Thanks
Gabe
I was able to install the rear turn signals, license plate LEDs, and reverse LEDs.
Does the front bumper have to be removed to install the switchback V3 Triton LEDs turn signal and the Osram CBI 5K bulbs. Or is there an easier way of installing them
Any advice is appreciated.
Thanks
Gabe
#3
Registered Member
I have a 2011 sedan and I was able to install the front turn indicator bulbs by going through the engine bay, although the air filter boxes have to be removed first.
But to change the headlight bulbs, you'll have to go through the wheel well.
Sorry, but not sure how to change the foglight bulbs.
But to change the headlight bulbs, you'll have to go through the wheel well.
Sorry, but not sure how to change the foglight bulbs.
#4
Registered User
iTrader: (8)
Hey guys, I recently purchased the Osram CBI 5K D2S bulbs, V3 Red LED Lights for the rear turn signals, V3 Switchback 5K LED turn signals, CREE MT-G2 High Power LED fog lights, 5K Vleds reverse lights, 5K license plate LEDs, and 5K City LEDs.
I was able to install the rear turn signals, license plate LEDs, and reverse LEDs.
Does the front bumper have to be removed to install the switchback V3 Triton LEDs turn signal and the Osram CBI 5K bulbs. Or is there an easier way of installing them
Any advice is appreciated.
Thanks
Gabe
I was able to install the rear turn signals, license plate LEDs, and reverse LEDs.
Does the front bumper have to be removed to install the switchback V3 Triton LEDs turn signal and the Osram CBI 5K bulbs. Or is there an easier way of installing them
Any advice is appreciated.
Thanks
Gabe
Last edited by Mik3G37S; 06-23-2014 at 12:42 PM.
#5
Registered User
Honestly, just make your life 100x easier and just jack up the car and take the wheel off.
Yes, it adds an extra 15 minutes per side but you gain SO MUCH working room and you will save so much skin on your knuckles and you wont scream all these bad words.
So in conclusion.....Jack up the driver side, remove wheel, remove all the plastic rivets in the wheel well, then loosen the 4 bolts on bottom of the bumper and BOOM, the entire fender lining comes out for extremely easy installation of all the bulbs, including fog.
Just set aside 2 hours of your time to knock this all out.
Yes, it adds an extra 15 minutes per side but you gain SO MUCH working room and you will save so much skin on your knuckles and you wont scream all these bad words.
So in conclusion.....Jack up the driver side, remove wheel, remove all the plastic rivets in the wheel well, then loosen the 4 bolts on bottom of the bumper and BOOM, the entire fender lining comes out for extremely easy installation of all the bulbs, including fog.
Just set aside 2 hours of your time to knock this all out.
#7
Registered User
Trending Topics
#10
Registered User
Osram Xenarc Cool Blue Intense 5000K D2S bulbs
Amber LED Turn Signals w/ load resistors
7W 5000K LED Fog
I will too post pics
#12
Registered User
iTrader: (8)
Any of you guys got to install the V3 Triton turn signals/switchbacks? I got my V3 amber LEDs that I have to install after getting my custom Headlights with dual evil iron man LEDs, can you guys post some pics videos? And any tips on installing thode V3s? Any issues or suggestions on the resistor placement?
Please let me know, thanks
Please let me know, thanks
#14
Registered User
iTrader: (8)
I know they are bright as hell, nothing compares to them, especially the new ones upgraded ones with more LEDs.. that I can tell you without a doubt... but I thought I'd ask people who have them if there were any issues installing them or any advice on the install or placement of the resistors.
#15
Hey guys, I recently replaced my halogen bulbs with LED bulbs. I also swapped the original lenses with STI clear lenses. work done by oneighty.
this is my current V3 setup:
5K switchback LEDs - front turn signals
Red Leds - rear turn signals
5K LEDs- license plate, city lights, reverse lights
5K LED fog lights
I love the new setup.
Will post pictures soon
this is my current V3 setup:
5K switchback LEDs - front turn signals
Red Leds - rear turn signals
5K LEDs- license plate, city lights, reverse lights
5K LED fog lights
I love the new setup.
Will post pictures soon